Bonjour,
Je suis un nouvel utilisateur d'X-FMC, et j'ai bien suivi le tutoriel d'installation de celui-ci (sauf les données NAVIGRAPH que je n'ai pas téléchargé). J'ai égallement téléchargé le fichier config du Boeing 747-400 United présent sur le forum et l'ai mis dans le dossier "X-Plane 10\Aircraft\Heavy Metal\B747-400 United\" ; le fichier config comportant bien le même nom que le .acf.
Je lance donc X-Plane, j'entends la petite voix qui me dit qu'X-FMC est "OK", j'arrive ensuite dans mon avion (le Boeing 747-400 United), et la fenêtre d'X-FMC me dit en bas "Fail in Vsclimb speed".
Bon, je regarde alors dans "IDENT", et je vois qu'il n'y a rien d'indiqué sur mon avion, les champs sont vides. Et lorsque je fais mon plan de vol, quand je veux rentrer mon CRZ ALT, X-Plane crashe.
J'ai vu qu'il y avait un sujet simillaire au mien, mais l'anglais n'est pas mon fort malheureusement et j'ai rien compris... 
Je suis sous Windows 7 64bits. et X-Plane est en version 10.05r1.
Merci.
----
Translation :
Hello,
I am a new X-FMC user , and I followed the installation tutorial (except for Navigraph I have not downloaded). I also downloaded the config for United Boeing 747-400 on this forum and put it in the "X-Plane 10 \ Aircraft \ Heavy Metal \ United B747-400 \" and the config file with the well same name as the. acf.
I therefore launch X-Plane, I hear the little voice that tells me that X-FMC is "OK", then I get in my plane (Boeing 747-400 United), and X-FMC window says below "Fail in Vsclimb speed".
Well, when I look in "IDENT", and I see that there is nothing shown on my plane, the fields are empty. And when I make my flight plan, when I get my CRZ ALT, X-Plane crashes.
I saw that there was a topic simillaire mine, but English is not my strong point and unfortunately I did not understand ...
I am running Windows 7 64bit. and X-Plane version is 10.05r1.
Thank you.
Bonjour,
Bienvenue à toi sur X-FMC.
Il convient dans un premier temps de regarder si tu as tous les droits sur les dossiers de X-Plane. Cela ressemble à un problème de lecture / écriture sur les fichiers.
Après, j'avoue que sans les fichiers de Navigraph, cela fonctionne mais de manière un peu bancale.
Quelle route as-tu saisi ? As-tu fait un reset de X-FMC avant de lancer ton vol ?
A bientôt
---------
Translation :
Hello,
Welcome to you on X-FMC.
We Should initially see if you have all the rights on the files of X-Plane. This looks like a problem reading / writing files.
After that, I admit that without Navigraph files, it works but it's a bit wobbly.
What route did you entered? Did you do a reset of X-FMC before starting your flight?
See you soon
Merci pour la réponse pour commencer.
Alors j'ai bien vérifier les droits et j'ai bien les droits de lecture écriture sur le fichier et j'ai égallement fait des "reset FMC" avant chaque préparation de vol.
Mais ce que j'ai remarqué il n'y a pas longtemps, c'est que sur le x737 Boeing 737-800 d'X-Plane.org où le fichier config est fourni avec, X-FMC reconnait l'avion et je peux l'utiliser sans problèmes avec même les mêmes routes que j'ai tenté de rentrer avec le 747.
J'en ai donc conclu qu'il s'agirait surement du fichier config du 747 lui même qui posait un problème avec le X-FMC.
Donc voilà ce que je peux te renseigner de plus.
---------------------------
Translation:
Thank you for the response To start,
So I have checked the rights and I have read write rights on the file and I have also done "reset FMC" before each flight preparation.
But I noticed not long ago, that the x737 Boeing 737-800 for X-Plane. Org where the config file is supplied with X-FMC recognizes the plane and I can use it without problems even with the same roads as I tried to go with the 747.
I therefore concluded that it would surely config file the 747 itself, which was a problem with the X-FMC.
So here this is what I can tell you .
Attention les noms du cfg et acf doivent être rigouresement identiques !
xyz123.acf = xyz1234.cfg
-----------
Beware, names have to match exactly !!!
xyz123.acf = xyz1234.cfg
C'est pourtant bien le cas. Dans mon dossier du Boeing 747 il y a "747 -400 United.acf" et "747 -400 United.cfg".
Etrange !
Il y a un soucis avec la casse... Je pense
La casse ? C'est-à-dire ?
Bon, finallement le problème est résolu suite à une réinstallation complète d'X-Plane et sa mise à jour en version 10.10r2. Il reconnait mon Boeing 747-400 et j'ai bien le "Model Loaded".